How to build a Lathe Chuck Storage + Lathe Bed Scraper and Protector + Simple Device for Extracting
These Storage ideas are primarily adaptable to anyone using one of the many 4 Jaw Scroll Chucks that exist, with the cost of many of these Chuck systems often exceeding the cost of the Lathe it is important that they are looked after and protected from damage and loss....
|
| |
How to build a Lathe Cross Slide Cover + Tool Tidies + Magnet #2 + Laminated Data Sheet Holder + Ban
The Cross Slide [Banjo] on the Hegner Lathe I use, has what I would term an...
|
| |
How to build a Lathe Cup Chucks and Faceplate Chucks for The Vacuum Chuck System
The beauty of making your own is you can adapt the Size to your exact needs and requirements which will change as you progress with finding the many uses you can put a Vacuum Chucking System to....
|
| |
How to build a Lathe Deep Boring System Part i The Boring Bar
Like many Hobbyist Woodturners I have over the years collected numerous Tools and Accessories some of which have been more successful than others, the success that had for along time alluded me was making Hollow Vessels, even with all the various aids that are supposed to make it oh so simple....
|
| |
How to build a Lathe Dovetail Groove Dividers + Handy Rule Aid + Magnet #1 + Button Jaw Capacity Cha
I have 4 sets of Dovetail Type Expanding Jaws of which 3 are in constant use, each requiring a different size Recess in the work piece for the Jaws to locate into....
|
| |
How to build a Lathe Drilling Depth Gauge for The Tailstock + Magnet #4
This article details the modification that I made to the Tailstock of my Lathe enabling me to accurately and consistently gauge and control the Drilling Depth of any drilling operation whether using Twist Drills, Brad Point Drills, Spade Cutters or Forstner Bits....
|
| |
|
How to build a Lathe Drilling Jig
Drilling accurate holes in a workpiece held in the lathe can be difficult to achieve accurately, especially if the angle to the wood must be repeatable. Bushings and guides are available but soon become worn and setting of accurate drilling angles is difficult. To solve the problem, a jig was produc...
|
| |
How to build a Lathe Extension to Standard Button Jaws + Capacity Charts
I set about making a simple set of Extension Jaws to fit the original Jaw Plates of the 250mm system these would have a nominal diameter of 360mm (14...
|
| |
How to build a Lathe Faceplate Ring Locater Jig
A handy project to help you quickly and easily find the centre of your bowl blank....
|
| |
How to build a Lathe Fingernail Jig + Skew Grinding Jig + Tip Holder for Easy Grinding
The Fingernail Grind Profile for Gouges is one of the innovations of the last decade that has enabled Woodturners to improve the scope and versatility of the Gouge, and has spawned a number of Jigs to enable anyone to convert the Gouge to this profile and then Sharpen it on a consistent basis....
|
| |
How to build a Lathe Grinding Jig Part i
Turning Tools need regular Sharpening and for this you require a means of Grinding this can be either a Bench Grinder, or a Wet Grinder these are of course not the only options but they are the two most popular....
|
| |
How to build a Lathe Grinding Jig Part ii
In part 1 of this article I described how I made the two Standard Type Rests for the Bench Grinder, in part 2 I describe how I made a Gouge Grinding Jig....
|
| |
|
< Previous
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
Next >
|
