How to build a Lathe Guard
After nearly losing a finger to a spinning three-jaw lathe chuck, I came up with a guard that keeps my fingers safely away from the chuck...
|
| |
How to build a Lathe Hollow Form and Other Tools + Hollow Form Shavings Removers
I have made over the years many such Tools some are in regular use others never fulfilled their promise and have either been recycled or discarded, the beauty is they do not have to cost a fortune....
|
| |
How to build a Lathe Indexing Head for The Lathe + Spindle Lock
Both my Lathe and Chuck have a means of Indexing, but in each case the Divisions are 24 giving a Division Angle of 15...
|
| |
How to build a Lathe Mini Button Jaw Set + Capacity Charts
I soon realised that in fact a Mini Button Jaw Set would be more versatile and flexible in use and below I detail my solution for making such a set of Jaws....
|
| |
How to build a Lathe Mini Gripper Support + Revolving Center and Jacobs Chuck Storage + Tailstock Pl
I think the Craft Supplies Mini Gripper is a fantastic little Chuck (if that is in fact what it is) that is both simple and efficient, every Woodturner should own one....
|
| |
How to build a Lathe Mini Power Sander + Mini Sanding Disc Storage + Covers
There are a number of items that are Turned in the Chuck, and then Parted off, such as Pots, Weed Vases, Candlesticks, Ring Stands etc. etc. The bottom or base of these items have to be finished off before being sealed, every one of us has a different method using a combination Chisels to remove the...
|
| |
|
How to build a Lathe Platform + Ball Cutting Jig + Router Holder Sled + Copying Sled Part i
This Article will be in three parts with the first two parts covering several Holders for various items used to Decorate, Form, Copy or Drill Items held in the Lathe....
|
| |
How to build a Lathe Platform + Ball Cutting Jig + Router Holder Sled + Copying Sled Part ii
In Part II of this article I describe three Holders, with four uses, that I have developed for use with the Sled described in Part I, these are the Dremel Holder, A Ball Cutting Jig and A Drill Guide....
|
| |
How to build a Lathe Platform + Ball Cutting Jig + Router Holder Sled + Copying Sled Part Iii
The Base Board is the Hub of the System and you need to think through all the things you want to achieve and also in the future, you also have to consider the fact that the Board will extend well beyond the Lathe so you do not want it to be too Large and then again you do not want it to be so Small...
|
| |
How to build a Lathe Platform + Ball Cutting Jig + Router Holder Sled + Copying Sled Part iv
In the final part of this article I detail the various ways of for Pivoting, Guiding and Fixing the Sled in its various applications. I have found the concept to be very flexible in both design and use and that most eventualities are covered within the design and should new requirements be needed th...
|
| |
How to build a Lathe Pole - and Shave Horse Design
I have been using these designs for about 3 years regularly at shows so they have stood the test of time as portable units, easily fitting into a car or small trailer along with tools, stock and wood. The Lathe and shave horse can be assembled in less.....
|
| |
How to build a Lathe Pole - End Vise
Making Handles and Chair Rung Tenons. Text by John Alexander and photos by Peter Follansbee.Viires, Woodworking in Estonia, illustrates a simple pole lathe erected on the end vise of a cabinetmaker...
|
| |
|
< Previous
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
Next >
|
